Physical properties of ultrafine-grained magnesium based alloys prepared by various severe plastic deformation techniques
Fyzikální vlastnosti jemnozrnných hořčíkových slitin připravených různými technologiemi
dizertační práce (OBHÁJENO)
Zobrazit/ otevřít
Trvalý odkaz
http://hdl.handle.net/20.500.11956/68971Identifikátory
SIS: 85253
Kolekce
- Kvalifikační práce [10932]
Autor
Vedoucí práce
Oponent práce
Dlouhý, Antonín
Kalvoda, Ladislav
Fakulta / součást
Matematicko-fyzikální fakulta
Obor
Fyzika kondenzovaných látek a materiálový výzkum
Katedra / ústav / klinika
Katedra fyziky materiálů
Datum obhajoby
8. 9. 2014
Nakladatel
Univerzita Karlova, Matematicko-fyzikální fakultaJazyk
Angličtina
Známka
Prospěl/a
Klíčová slova (česky)
Ultra-jemnozrnné materiály, slitiny hořčíku, metody intenzivní plastické deformace, ekvivalentní vložená deformace, vývoj mikrostrukturyKlíčová slova (anglicky)
Ultrafine-grained (UFG) materials, magnesium alloys, severe plastic deformation (SPD) techniques, equivalent imposed strain, microstructure evolutionNázev práce: Fyzikální vlastnosti jemnozrnných hořčíkových slitin připravených různými technologiemi Autor: Jitka Stráská Katedra / Ústav: Katedra fyziky materiálů Vedoucí doktorské práce: Doc. RNDr. Miloš Janeček, CSc. Abstrakt: Tato disertační práce je zaměřena na komplexní studium ultra-jemnozrnné hořčíkové slitiny AZ31 připravené dvěma různými metodami intenzivní plastické deformace: extruzí následovanou protlačováním lomeným kanálem (EX-ECAP) a torzí za vysokého tlaku (HPT). V úvodní části práce jsou detailně rozebrány různé metody intenzivní plastické deformace. V navazující části jsou shrnuty výsledky experimentů. Použitím širokého spektra experimentálních technik byla charakterizována především mikrostruktura, mechanické vlastnosti a struktura mřížových poruch materiálu. Byla zkoumána i strukturní stabilita ultra- jemnozrnné mikrostruktury za zvýšených teplot a za použití rovnic pro růst zrn a Arrheniovy rovnice byly spočteny aktivační energie pro růst zrn pro různé teplotní obory. Měřením hustoty dislokací byl nalezen teplotní interval zotavování a následného růstu zrn. Výsledky měření velikosti růstu zrn byly navíc použity pro ověření Hall-Petchovy rovnice. V poslední části práce je diskutována efektivita dvou zkoumaných metod intenzivní plastické deformace především pro zjemnění zrna. HPT se...
Title: Physical properties of ultrafine-grained magnesium based alloys prepared by various severe plastic deformation techniques Author: Jitka Stráská Department / Institute: Department of Physics of Materials Supervisor of the doctoral thesis: Doc. RNDr. Miloš Janeček, CSc. Abstract: The objective of the doctoral thesis is the complex investigation of ultrafine-grained magnesium alloy AZ31 prepared by two different severe plastic deformation techniques, in particular the hot extrusion followed by equal-channel angular pressing (EX-ECAP) and high pressure torsion (HPT). These severe plastic deformation methods, and as well as many others, are described in detail in the introductory theoretical section. Experimental results are summarized in the following experimental part of the thesis. Mechanical properties, lattice defect structure and especially microstructure were investigated using various experimental techniques. Thermal stability of ultrafine-grained microstructure of AZ31 after EX-ECAP was investigated and the activation energies for grain growth in different temperature ranges were calculated using kinetic equation for grain growth and Arrhenius equation. Results from the dislocation density measurements proved temperature ranges of the recovery and the following grain growth. Results from the...