Zobrazit minimální záznam

Mikrostruktura a textura titanu připraveného přáškovou metalurgií
dc.contributor.advisorStráský, Josef
dc.creatorKozlík, Jiří
dc.date.accessioned2021-03-25T20:03:41Z
dc.date.available2021-03-25T20:03:41Z
dc.date.issued2018
dc.identifier.urihttp://hdl.handle.net/20.500.11956/98672
dc.description.abstractKomerčně čistý titan byl připraven jako objemový materiál pomocí práškové metalurgie, konkrétně pomocí kryogenního mletí a sintrování elektrickým prou- dem, s cílem připravit ultrajemnozrnný materiál se zvýšenou pevností. Mikro- struktura prášků po mletí byla detailně zkoumána pomocí transmisního EBSD - nové metody, která umožnila první přímé pozorování textury uvnitř částic. Tato textura je podobná textuře po válcování díky podobnosti deformačních mecha- nismů. V prášku byla pozorována zrna s velikostí pod 100 nm. Vliv parametrů sintrování na vlastnosti materiálu byl studován pomocí skeno- vací elektronové mikroskopie včetně EBSD, rentgenové difrakce a pomocí měření mikrotvrdosti. Byl odhalen kompromisní vztah mezi porozitou a velikostí zrna - zcela neporézní materiál s ultrajemnozrnnou strukturou není možné připravit. Zvýšený obsah kyslíku je hlavním faktorem přispívajícím ke zpevnění materiálu, zatímco porozita má značně nepříznivý vliv na mechanické vlastnosti. Textura prášku byla za- chována i v sintrovaném materiálu. Možnost stabilizace ultrajemnozrnné struktury mechanickým legováním Ti s oxi- dem ytritým byla studována se smíšenými výsledky. Stabilizace byla úspěšná,...cs_CZ
dc.description.abstractBulk commercially pure titanium was prepared by powder metallurgy, namely by cryogenic milling and spark plasma sintering, with aim to produce ultra-fine grained material with enhanced strength. The microstructure of milled powders was investigated in detail by a novel method called transmission EBSD, which allowed the first direct observation of texture within the powder particles. This texture is similar to rolling texture, because of the similar nature of the defor- mation during milling. Microstructure observations revealed grains with the size under 100 nm. The influence of sintering parameters on material properties were studied by scan- ning electron microscopy including EBSD, X-ray diffraction and by microhardness measurements. The trade-off relationship between porosity and grain size was identified, fully dense material with ultra-fine grained microstructure could not be produced. Increased oxygen content was identified as a main strengthening factor, while porosity has significant deteriorating effect on mechanical properties. The texture of powder was retained in the bulk material. The possibility of stabilizing the microstructure by mechanical alloying of Ti with yttrium oxide nanoparticles was investigated with mixed results. The stabiliza- tion was successful, but several issues...en_US
dc.languageEnglishcs_CZ
dc.language.isoen_US
dc.publisherUniverzita Karlova, Matematicko-fyzikální fakultacs_CZ
dc.subjecttitaniumen_US
dc.subjectcryogenic millingen_US
dc.subjectspark plasma sinteringen_US
dc.subjecttextureen_US
dc.subjecttransmission EBSDen_US
dc.subjecttitancs_CZ
dc.subjectkryogenní mletícs_CZ
dc.subjectsintrování elektrickým proudemcs_CZ
dc.subjecttexturacs_CZ
dc.subjecttransmisní EBSDcs_CZ
dc.titleMicrostructure and Texture of Titanium Prepared by Powder Metallurgyen_US
dc.typediplomová prácecs_CZ
dcterms.created2018
dcterms.dateAccepted2018-06-06
dc.description.departmentKatedra fyziky materiálůcs_CZ
dc.description.departmentDepartment of Physics of Materialsen_US
dc.description.facultyMatematicko-fyzikální fakultacs_CZ
dc.description.facultyFaculty of Mathematics and Physicsen_US
dc.identifier.repId189565
dc.title.translatedMikrostruktura a textura titanu připraveného přáškovou metalurgiícs_CZ
dc.contributor.refereeChráska, Tomáš
dc.identifier.aleph002190627
thesis.degree.nameMgr.
thesis.degree.levelnavazující magisterskécs_CZ
thesis.degree.disciplinePhysics of Condensed Matter and Materialsen_US
thesis.degree.disciplineFyzika kondenzovaných soustav a materiálůcs_CZ
thesis.degree.programFyzikacs_CZ
thesis.degree.programPhysicsen_US
uk.thesis.typediplomová prácecs_CZ
uk.taxonomy.organization-csMatematicko-fyzikální fakulta::Katedra fyziky materiálůcs_CZ
uk.taxonomy.organization-enFaculty of Mathematics and Physics::Department of Physics of Materialsen_US
uk.faculty-name.csMatematicko-fyzikální fakultacs_CZ
uk.faculty-name.enFaculty of Mathematics and Physicsen_US
uk.faculty-abbr.csMFFcs_CZ
uk.degree-discipline.csFyzika kondenzovaných soustav a materiálůcs_CZ
uk.degree-discipline.enPhysics of Condensed Matter and Materialsen_US
uk.degree-program.csFyzikacs_CZ
uk.degree-program.enPhysicsen_US
thesis.grade.csVýborněcs_CZ
thesis.grade.enExcellenten_US
uk.abstract.csKomerčně čistý titan byl připraven jako objemový materiál pomocí práškové metalurgie, konkrétně pomocí kryogenního mletí a sintrování elektrickým prou- dem, s cílem připravit ultrajemnozrnný materiál se zvýšenou pevností. Mikro- struktura prášků po mletí byla detailně zkoumána pomocí transmisního EBSD - nové metody, která umožnila první přímé pozorování textury uvnitř částic. Tato textura je podobná textuře po válcování díky podobnosti deformačních mecha- nismů. V prášku byla pozorována zrna s velikostí pod 100 nm. Vliv parametrů sintrování na vlastnosti materiálu byl studován pomocí skeno- vací elektronové mikroskopie včetně EBSD, rentgenové difrakce a pomocí měření mikrotvrdosti. Byl odhalen kompromisní vztah mezi porozitou a velikostí zrna - zcela neporézní materiál s ultrajemnozrnnou strukturou není možné připravit. Zvýšený obsah kyslíku je hlavním faktorem přispívajícím ke zpevnění materiálu, zatímco porozita má značně nepříznivý vliv na mechanické vlastnosti. Textura prášku byla za- chována i v sintrovaném materiálu. Možnost stabilizace ultrajemnozrnné struktury mechanickým legováním Ti s oxi- dem ytritým byla studována se smíšenými výsledky. Stabilizace byla úspěšná,...cs_CZ
uk.abstract.enBulk commercially pure titanium was prepared by powder metallurgy, namely by cryogenic milling and spark plasma sintering, with aim to produce ultra-fine grained material with enhanced strength. The microstructure of milled powders was investigated in detail by a novel method called transmission EBSD, which allowed the first direct observation of texture within the powder particles. This texture is similar to rolling texture, because of the similar nature of the defor- mation during milling. Microstructure observations revealed grains with the size under 100 nm. The influence of sintering parameters on material properties were studied by scan- ning electron microscopy including EBSD, X-ray diffraction and by microhardness measurements. The trade-off relationship between porosity and grain size was identified, fully dense material with ultra-fine grained microstructure could not be produced. Increased oxygen content was identified as a main strengthening factor, while porosity has significant deteriorating effect on mechanical properties. The texture of powder was retained in the bulk material. The possibility of stabilizing the microstructure by mechanical alloying of Ti with yttrium oxide nanoparticles was investigated with mixed results. The stabiliza- tion was successful, but several issues...en_US
uk.file-availabilityV
uk.grantorUniverzita Karlova, Matematicko-fyzikální fakulta, Katedra fyziky materiálůcs_CZ
thesis.grade.code1
dc.contributor.consultantHarcuba, Petr
dc.contributor.consultantSrba, Ondřej
uk.publication-placePrahacs_CZ
uk.thesis.defenceStatusO
dc.identifier.lisID990021906270106986


Soubory tohoto záznamu

Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail

Tento záznam se objevuje v následujících sbírkách

Zobrazit minimální záznam


© 2017 Univerzita Karlova, Ústřední knihovna, Ovocný trh 560/5, 116 36 Praha 1; email: admin-repozitar [at] cuni.cz

Za dodržení všech ustanovení autorského zákona jsou zodpovědné jednotlivé složky Univerzity Karlovy. / Each constituent part of Charles University is responsible for adherence to all provisions of the copyright law.

Upozornění / Notice: Získané informace nemohou být použity k výdělečným účelům nebo vydávány za studijní, vědeckou nebo jinou tvůrčí činnost jiné osoby než autora. / Any retrieved information shall not be used for any commercial purposes or claimed as results of studying, scientific or any other creative activities of any person other than the author.

DSpace software copyright © 2002-2015  DuraSpace
Theme by 
@mire NV